MISOLIMA eAlbert Control 8 gives
   
easy hardware I/O, relay and sensor control...
    Use your PC for more than just running software on it.
Control relays, hardware and sensors or make your own
DIY alarm system for vehicle, home, office or company...
Embedded system
with integrated OS
and DOLLx8 software
   
 

MISOLIMA eAlbert Control 8
DIGITAL I/O WITH 10-bit ADC's

High performance ADC
 Fast 8 channels/10-bit ADC

Inn and Out ports (I/O Ports)
 Fast 8-bit I/O Ports with independent control with settings for automatic puls down to 0.01s per channel. Switch inputs from switches and sensors. Built in buzzer,

Relay output
2x max 30Vdc 2A relay output

Microcontroller
 faster 18MHz Atmel microcontroller with Real Time Operating System (RTOS), 2 COM ports, Internal CompactFlash memory, DOLLx8 Network Protocol etc.

DOLLx8 and communication protocol
DOLLx8 intelligent data protocols.

PIN
PORT 1 Connector Pins
PIN
1
 Vin (Out)   GND
2
3
 Vin REL #1   Vin REL #2
4
5
 Vout REL #1   Vout REL #2
6
7
 Buzzer In (TTL)   GND
8
9
 +5V (USB)   GND
10
11
 SW #2 P1.4   SW #3 P1.5
12
eAlbert DOLLx8


PIN
PORT 2 Connector Pins
PIN
1
 Vin (Out)   GND
2
3
 ADC #2 P1.1   ADC #1 P1.0
4
5
 GND   +5V Out
6
7
 IO8 P0.7   IO7 P0.6
8
9
 IO6 P0.5   IO5 P0.4
10
11
 IO4 P0.3   IO3 P0.2
12
13
 IO2 P0.1   IO1 P0.0
14
15
 MCU Reset   GND
16
17
 ON/OFF Power   ESW P1.5
18
19
 SW #2 P1.4   SW #1 P1.3
20
eAlbert DOLLx8

PIN
"EXT" PORT RJ-45 Connector
PIN
1
 RX DOLLx8   TX DOLLx8
2
3
 NC   NC
4
5
 NC   GND
6
7
 +Vin (Out)   +5Vdc USB
8
eAlbert DOLLx8

PIN
"PC" PORT RJ-45 Connector
PIN
1
 TX DOLLx8   RX DOLLx8
2
3
 NC   NC
4
5
 NC   GND
6
7
 +Vin (Out)   +5Vdc USB
8
eAlbert DOLLx8


MISOLIMA eAlbert DOLLx8 back panel with I/O port connectors and RJ-45 communication ports.

Control power for light and devices via USB or GSM with the new text-based embedded DOLLx8 network protocol.

eAlbert Control 8 from MISOLIMA is a sophisticated I/O device managed by the DOLLx8 Network Protocol. By using simple ASCII characters, all ports and functions can be managed direct via GSM*, RS-232 or USB serial port. By connecting eAlbert Control 8 to eBonnie 15-368 AVL and/or eClyde 15-368 GSM system, you will also be able to control this device remotely via SMS or GPRS by simply sending DOLLx8 commands via GSM. eAlbert Control 8 has ports to control the relays on the MISOLIMA eThomas REL22.

MISOLIMA eAlbert DOLLx8 serial to embedded systems with a completely new embedded interface and a revamped engine is a embedded software-based solution that allows you to control electricity and sensors via serial port using DOLLx8 network, effectively turning your computer into a low-cost control system for home and office automation or alarm system with GSM capabilities. As a result, your serial port like RS-232 or USB in connection with GSM or Internet can control electricity and sensors to and from anywhere.

The new eAlbert boasts the latest in innovative embedded technology and uses many of the breakthroughs that exist in the DOLLx8 embedded network protocol.

 o eCharlie U2R
 o eThomas REL22
 o eOscar KeyPad
 o eAlbert DOLLx8
 o eBonnie 15-368 AVL
 o eClyde 15-368 GSM
 o ePAT MCU
 o eGSM Q4 1800
 o eLeon Horizon60
 o eMichael MiRAS
 o eJames GPS III
 
 o eMessanger 220
 o eBalletPC
 o eGraFIKO 640 TFT
 

 Company: MISOLIMA
 Product ID: 002A03XXX
 DOLLx8 Ver.: 3.0r18
 HWUART Baudrate: 38400
 Device: eAlbert DOLLx8
 Hardware Ver.: 1.0r02
 Software Ver.: 1.0r06
 Software Date: 25 JAN 2011
 MCU Speed: 18.432 MHz

Features and Specifications of eAlbert DOLLx8
Ports : 8-bit TTL I/O ports (with EMI filer)
2x 10-bit ADC with internal voltage referance
3x switch input for Make or Brake mode
1x RS-232 TTL port and 1x DOLLx8 port
Relays: Two max 30Vdc/3A miniature relays
Audio: Internal buzzer
Network protocol: DOLLx8 over USB or RS-232 (ASCII based)
Power: Built-in DC-DC switching power supply (5-28Vdc)
MCU: 18.432 Mhz ATMEL MCU (re-programmable)
Software: DOLLx8 version 3.18
Alarm: Full alarm system with connection to eOscar Keypad, eMessanger character display and eBonnie 15-368 AVL or eClyde 15-368 GSM plus light, temperature, smoke and motion sensors.
Display: LED indication on front (COM, PWR ERR, Data port, Alarm, Relay Status, Switch status and RxD/TxD)
USB and external power indication
Connectors: Port #1 12 pin. Port #2 20 pin (dual raw 2mm)
RJ-45 (DOLLx8 extension and PC-PORT)
Power Switch: Front pannel PWR switch with disable on Port1
Dimensions: W=105mm, D=83mm, H=26mm
Operating temperature: -40°C ~ +85°C
Storage temperature: -55°C ~ +100°C
* require GSM device connected to eAlbert DOLLx8

How does DOLLx8 work?

DOLLx8 stands for Digital One Line Link and it is well known that if your devices can do more things, you can also do more things with it. Check out how the easy to use and easy to program or control capabilities of DOLLx8 Certified devices can revolutionize the way you control your electrical devices at home, office, workplace or in vehicles. As embedded system DOLLx8 Certified devices can be controlled via RS-232, USB or GSM with easy to use text messages.

All you need to get started is one or more DOLLx8 Certified devices that links to each other with standard PC network cable with RJ-45 connectors. All is made easy because DOLLx8 Certified devices are able to connect, discover and communicate with each other over a DOLLx8 Certified network – that again might connect to one or more PC's for I/O control. In fact more than one PC can share the control of the DOLLx8 Certified devices that might also carry Username and Password functions for security reasons.

My page history: James | PatMCU | Michael | Projects01 | CharlieU2R | Clear History
 
MISOLIMA 
www.misolima.com and its brand MISOLIMA© is licensed 
Copyright® 2000/11 - All rights reserved. 
Privacy Policy | Return Policy | Terms and Conditions | Terms and Conditions |
Note: All the dates (DD.MM.YY) and times are given in Far East Time (UTC+07:00)